It is amazingly well-to-do to make DIY grow light for your seedlings . In this mail , I ’ll give you footmark by step instructions for how to make your own , including an inexpensive and a dim-witted stand for hanging the fix too .
If you plan tostart your seeds indoors , then you will definitely need a grow igniter for your seedlings . The good tidings is that you do n’t have to expend a ton of money to get set up !
In this tutorial , I will show you how to make your own seedling grow light , step by step . Plus , as a bonus , I ’ll share my teaching for building a custom stand for them too .
My seed starting light and stand in use
board of Contents
Inexpensive DIY Seed Starting Grow Lights & Stand
For this project , I used a 48″ lighting fixture , which bid a sound amount of distance . you could fit twostandard sized seed traysend - to - death underneath this DIY get light , or four of them side - by - side .
But , if you prefer , you could apply a shorter fixture , and adjust the measurements of the homemade stand to correspond the sizing . Since this task is so dewy-eyed , it ’s light to customize to your exact motivation .
How To Make A Grow Light For Seedlings
You do n’t require any putz to make this grow light for seedlings , just a few inexpensive supplies . Everything you need can be receive online , or at your local ironware or household betterment store .
Supplies Needed
Steps For Assembling The DIY Grow Light
full time : 10 - 15 moment
stride 1 : Prepare the fixing – Remove thelight fixturefrom the box , and lay it upside down on a categorical , sturdy airfoil . If your fixture came with chains and S thieve for hang , put them by for now .
footprint 2 : make the bulb – It ’s safer and easier to work with one acquire bulb at a time . Rather than unpacking them both right away , start by opening only one of them .
Step 3 : instal the bulbs – It ’s very easy to deploy the fluorescent bulbs into the fixture . Take one bulb firmly in your hands and line up the ends with the mechanisms on both side of the fixture .
Then gently press down on the ends to toss off the bulb into place ( do not push down on the glass part of the fluorescent bulb ) . Repeat to set up the second light bulb into the fixing .
pace 4 : Attach the pay heed hardware – Carefully turn over the reparation over . Find the two gob or slits located on either end of the top of the light fixture . This is where you will attach the hooks .
swoop one hookinto the trap on one end of the loose fixing . Attach one part ofchainto the other side of the S hook .
Repeat on the paired end of the fastness using one additional entropy bait and the other objet d’art of chain .
Then attach the last two S hooks , so there is one on the opposite ending of each piece of Ernst Boris Chain .
Step 5 : Secure the S hooks ( optional ) – you’re able to use pair of pliers to clamp the S lure where they ’re tie to the light fixture , if you prefer .
Do not clamp them to the other end of the chain however , or you wo n’t be able to align the height of your DIY seedling grow luminance .
Step 6 : Attach the adjustable hanger – If you want something nice and easier to use than chains and S hooks , I urge begin anadjustable hanger .
but confiscate the S hook from the loose end of the mountain range onto the lure of the adjustable hanger , and use pliers to securely clamp the S hook in place .
Related Post : When To Put Seedlings Under Lights & How Much
How To Make A Simple DIY Grow Light Stand
If you ’re looking for a dear way to hang your DIY seedling grow lights , I designed a customs duty viewpoint specifically for them .
This homemade stand is very sturdy and simple to make , but also lightweight and sluttish to take apart for memory .
This DIY produce light point of view is made from cheap textile that you may find online or at any home base improvement entrepot . I designed it specifically to hold one of my 48″ DIY seedling grow light .
But again , you could easily adapt this design to fit the breadth of any sized light fixture that you have . Here ’s what you ’ll want to construct it …
Steps For Assembling The DIY Grow Light Stand
Total time : 20 minutes
Step 1 : Measure & cut the frame while – Using the 10′ PVC pipework , tape step , andcutting tool , beat and cut seven pieces at the following length : one 50″ , two 18″ , and four 8 1/2″ piece .
Step 2 : put together the feet – Insert one 8 1/2″ piece of PVC into both end of one of theTee connector , leaving the top part of the Tee empty . Repeat this gradation to forgather the other groundwork .
tone 3 : Assemble the wooden leg – Insert one 18″ piece of PVC into the top of each Tee connection . You should now have two large Ts for the stage .
Step 4 : gather the top of the stand – Attach oneelbow connectoronto the top of each leg . Then attach the two cubital joint together using the 50″ part of PVC . Now your produce light stall is fully gather .
footstep 5 : Glue the while together ( optional ) – I wish that I can take my grow light bear apart for easy entrepot . But , if you choose , you’re able to attach the pieces together usingPVC gluefor additional stableness .
Just commemorate that this mucilage is permanent , so you wo n’t be able to take the sales booth apart again after this step .
Related Post : Beginner ’s Guide To Gardening On A Budget ( 19 sleazy DIY Tips )
How To Attach Your DIY Grow Lights To The Stand
It ’s very easygoing to attach your DIY seedling grow light to the stand using8″ cablegram zip standoff .
guarantee the tie around the top pole at both end of the stand . confiscate them hard , but not so tight that you ca n’t skid them along the pipe .
Slide the cable ties to either end of the top of the stand . Then , simply purloin the S sweetener from the end of each grow light string onto the ties . Use scissors hold to trim off the surplus check on the zip ties , if desired .
DIY grow light for seedlings are fast and easy to make , and do n’t cost a lot of money . Plus , if you make the fillip grow light stand for them , you ’ll have a full set up that you may put anywhere in your home .
If you ’re tired of seek to cypher out how to raise seeds by trial and computer error , then you demand to sign up up for my onlineSeed Staring Course ! This play and comprehensive self - pace course will teach you everything you need to do it about growing any eccentric of ejaculate you want . inscribe and commence today .
Otherwise , if you just need a quick refresher to get you going , then myStarting Seeds Indoors eBookis stark for you!Download your transcript right now .
More About Seedlings
Print Out This Tutorial
DIY Seedling Grow Lights
It ’s surprisingly easy and inexpensive to make DIY raise lights for seedlings . This light is bombastic enough to fit 2 - 4 flats of seedlings . Plus , the bonus grow lite rack make it easy to set them up anywhere in your menage .
Materials
Tools
Instructions
Assembling The Grow Light
Making The Grow Light Stand
